keyless entry question (1999/2000 years) [Archive] - GrandAmGT.com Forum

PDA

View Full Version : keyless entry question (1999/2000 years)


shortsexychica
06-13-2005, 04:56 PM
ok I'm going to try this again......I was wondering if y'all would be so kind to post the numbers off the back of your key fobs~keyless entry remotes for me so I can order the right one this time....Thanks in advance

Brandie

seffedman
06-13-2005, 04:58 PM
i just ordered a new one and programed it last night. I have a 2000 GT and the numbers on the back of the key chain is: GM/UTA 25665574 / FCC ID:KOBUT1BT. Hope that helps man.

shortsexychica
06-13-2005, 05:14 PM
it's woman and thanks....can ya PM the program inskructions? :wave:

rocketfast123
06-13-2005, 05:40 PM
the dealer should be able to tell you the right one. Unlike my 2001 that has three different versions :scream:

shortsexychica
06-13-2005, 05:52 PM
actually they want me to buy one from there for 85 bucks......and I won't...

rocketfast123
06-14-2005, 12:04 AM
They should still tell you the part number.

OneFastGT
06-14-2005, 06:06 AM
Ebay baby! You can get em for $10 usually...

seffedman
06-14-2005, 02:04 PM
Sorry about that chica, when I get home I'll send the instructions to you, it's really easy takes about three mins.

shortsexychica
06-14-2005, 08:00 PM
Ebay baby! You can get em for $10 usually...

got the one I have now from there....right at 20 bucks shipped and insured but was still the wrong one....

eBandit
06-15-2005, 03:27 PM
I got mine for a 2000 GA GT for 12 shipped on eBay, I cant find the instructions I used but I will post them tonight once I get back in.

eBandit
06-15-2005, 07:33 PM
Here are instructions to do a 2000, but I am told to do a 1999 or a 2001+ you need a scan tool.

2000 GRAND AM

Transmitter Programming

Important

Once the remote control door lock receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Up to 4 transmitters may be programmed.

To program the transmitters, perform the following procedure while seated in the vehicle driver's seat:

1. Close all the vehicle doors.

2. Remove the ignition key from the ignition lock cylinder.

3. Press and hold unlock on the door lock switch.

Important
To successfully enter the keyless entry programming/diagnostic mode, steps 4 through 6 must be completed within 25 seconds of pressing the door unlock switch.

4. While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do not rotate the ignition lock cylinder.

5. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain in the LOCK position for the rest of the procedure.

6. Release the door lock switch. The chime will sound three chimes to signal that transmitter programming/diagnostic mode is active.

7. Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for approximately 4 seconds. The chime will sound two times to signal that the transmitter has been programmed successfully.

8. Repeat step 7 for the rest of the transmitters (for a total of 4 transmitters).

9. To exit the transmitter programming/diagnostic mode:
Remove the ignition key from the ignition switch.


*for mine it took longer than expected on step 7 and I had to hold my transmitter up in the air towards the windshield; just hold the buttons until you hear the chime. (dont know why, it isnt the Keyless FOB battery because it has worked great for over a month and works at very long distances.

naeandnate
11-15-2005, 04:44 PM
i've got a 2000 GAGT and just called the dealership, they told me i need part # 25678793 but there's a guy on ebay who has part number 25695954 and says it'll fit?
i'm confused....