GrandAmGT.com Forum
http://www.pfyc.com GrandAmGT.com Premium Memership Signup
MilzyMotorsports.com   

Go Back   GrandAmGT.com Forum > Search Forums

Showing results 1 to 15 of 58
Search took 0.01 seconds.
Search: Posts Made By: HenryM
Forum: Technical Q&A 11-10-2015, 07:27 PM
Replies: 5
Views: 983
Posted By HenryM
no Kidding! I did have to do my happy dance...

no Kidding! I did have to do my happy dance though!
Forum: Technical Q&A 11-10-2015, 06:13 AM
Replies: 5
Views: 983
Posted By HenryM
long or multiple crank before starting

I've fighting a issue for about 1 1/2 years, it was random, by no means consistant. It began with my 3400, then after the install of the 3500. I used all new FPR, sensors, ICM, plugs, and wires. ...
Forum: Wheels, Tires, Brakes, & Suspension 07-26-2015, 03:23 PM
Replies: 20
Views: 6,424
Posted By HenryM
Curious,,,,,I have read several posts regarding...

Curious,,,,,I have read several posts regarding the use of 98-02 camaro rotors. Which I tried, and they were too thick at 1.25 inches, so I had to use 05 impala rotors which are only 1.18 inches...
Forum: All Go (Performance modifications) 07-05-2015, 01:19 PM
Replies: 4
Views: 2,300
Posted By HenryM
Now, my next item, does anyone know what exhaust...

Now, my next item, does anyone know what exhaust manifolds flow better than the 3400? I've heard rumors that the 3500 & 3900 exhaust manifolds from a Chevy Uplander are larger bore, anyone know for...
Forum: All Go (Performance modifications) 07-05-2015, 01:16 PM
Replies: 4
Views: 2,300
Posted By HenryM
I had been using the 3400 UIM, and switched over...

I had been using the 3400 UIM, and switched over to the 3500 UIM. The plate is drilled differently, so I had to do both the location holes, as well as threaded holes for the ICM & coils.
The 3500...
Forum: All Go (Performance modifications) 06-28-2015, 11:39 AM
Replies: 4
Views: 2,300
Posted By HenryM
LX5 Throttle Body

After reading HeC thread on using the TB from the Aurora 3.5, I decided to do the same. I tried to do as stock-looking a job as possible, even using the ICM mounting bracket from the LX9, and a TB...
Forum: Wheels, Tires, Brakes, & Suspension 05-18-2015, 04:56 PM
Replies: 5
Views: 5,901
Posted By HenryM
Control Arm refurb

About 5 years ago I had poly bushings installed in my aluminum control arms, was not a fan of the noise or harsh ride, but did like the improvement in handling.

This winter the grunting was...
Forum: Technical Q&A 03-09-2015, 04:51 PM
Replies: 4
Views: 930
Posted By HenryM
Update: Physically checking the 7x sensor, I...

Update: Physically checking the 7x sensor, I found that the connector which sits above, to be dirty, wet with salt splash water. I used electrical cleaner, pulled apart the connector/boot, cleaned...
Forum: Technical Q&A 03-09-2015, 06:54 AM
Replies: 4
Views: 930
Posted By HenryM
Thanks Starglow, I was just thinking the same...

Thanks Starglow, I was just thinking the same thing. Even though I just replaced both those sensor new when I did the engine swap, it's not unheard of that new electrical parts can go bad early on....
Forum: Technical Q&A 03-08-2015, 03:56 PM
Replies: 4
Views: 930
Posted By HenryM
Engine Trouble

Story line:
Friday after getting a hair cut, car sat for about 1 hour. Driving home, seems low on power. At stop light, car idled smoothly as always, but when I attempted to accelerate, engine...
Forum: Technical Q&A 02-15-2015, 10:57 AM
Replies: 5
Views: 3,229
Posted By HenryM
Any possibility of a purge valve/canister filter...

Any possibility of a purge valve/canister filter issue? The vent is supposed to close as fuel level rises in the tank, to prevent spillage. This also should allow the purge valve to open and draw...
Forum: All Go (Performance modifications) 12-20-2014, 06:07 AM
Replies: 7
Views: 5,129
Posted By HenryM
Great info! Thanks, I bought the TB and bracket...

Great info! Thanks, I bought the TB and bracket with intentions of doing this very thing once it warms up. I did the same for my coil-packs using both brackets. I will head back to the JY and get...
Forum: Technical Q&A 09-30-2014, 07:14 AM
Replies: 5
Views: 1,175
Posted By HenryM
Those are V6 mounts, the black one being next to...

Those are V6 mounts, the black one being next to the P/S rack, the very bottom bolt is kind of hard to access, but possible, I think its an 18mm bolt head. Definitely try to start the bolt by hand...
Forum: Wheels, Tires, Brakes, & Suspension 09-09-2014, 09:35 PM
Replies: 5
Views: 1,305
Posted By HenryM
Awesome guys, thanks for the info

Awesome guys, thanks for the info
Forum: Wheels, Tires, Brakes, & Suspension 09-09-2014, 04:48 PM
Replies: 5
Views: 1,305
Posted By HenryM
Trailing arm bushings

I've been wanting to replace the trailing arms due to bushings be old/cracked. Both Dorman and Napa arms come with only one bushing. I know there are two, both before and after the spindle. Both...
Showing results 1 to 15 of 58

 
Forum Jump

All times are GMT -6. The time now is 08:21 PM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 2011 GrandAmGT.com
MilzyMotorsports.com