GrandAmGT.com Forum
http://www.pfyc.com GrandAmGT.com Premium Memership Signup
RedlineGoods.com   

Go Back   GrandAmGT.com Forum > Search Forums

Showing results 1 to 15 of 44
Search took 0.02 seconds.
Search: Posts Made By: adrian13
Forum: Technical Q&A 08-27-2015, 09:36 PM
Replies: 5
Views: 1,210
Posted By adrian13
I have made no tunes yet to the pcm. I thought...

I have made no tunes yet to the pcm. I thought that I could idle it prior to the tune.

The MAF sensor is an LS1 and I swapped it out from the stock one. But it throws the code P0101 for both...
Forum: Technical Q&A 08-27-2015, 09:32 PM
Replies: 5
Views: 1,210
Posted By adrian13
yes this is a 3100 swap and from a 4T40E. The...

yes this is a 3100 swap and from a 4T40E. The wires harness plugs in correctly except for the siemens 60lb injectors. I had the multec 2 to ev1, I believe, adapters and its spraying fine. I had a...
Forum: Technical Q&A 08-27-2015, 08:42 PM
Replies: 5
Views: 1,210
Posted By adrian13
New Motor Install and Codes

I recently swapped to the LA1 and 4T45E. I have aftermarket everything in the LA1: custom Pistons, crank, cam, injectors... I started the car but it won't hold idle. I haven't tuned the past yet but...
Forum: Blowers,Turbos,N2O specific topics 08-14-2015, 01:35 PM
Replies: 7
Views: 2,986
Posted By adrian13
NM some of the questions. The last paragraph...

NM some of the questions. The last paragraph answered a lot of my questions. So where do you have the oil catch can pressure escaping to under the car? I know that a certain amount of the vapors, in...
Forum: Blowers,Turbos,N2O specific topics 08-14-2015, 01:27 PM
Replies: 7
Views: 2,986
Posted By adrian13
Aaron, do you have a pic of your current...

Aaron,

do you have a pic of your current engine bay with the mp62 setup? I was researching the thread where you and Milzy got into it over the pcv. Great discussion and points made.

I'm at the...
Forum: Technical Q&A 04-23-2015, 04:17 PM
Replies: 4
Views: 942
Posted By adrian13
Dexcool Question

Does anyone have issues with using Dexcool? I popped a head gasket several years ago and have seen the sludge left over from the coolant in the lines. Just seeing if glycol (green) 50/50 mix would...
Forum: Technical Q&A 04-17-2015, 03:27 PM
Replies: 20
Views: 4,925
Posted By adrian13
Nevermind. Young gun answered the question and I...

Nevermind. Young gun answered the question and I didn't realize it.
Forum: Technical Q&A 04-16-2015, 11:04 PM
Replies: 20
Views: 4,925
Posted By adrian13
Thanks AaronGTR. everything is looking good so...

Thanks AaronGTR. everything is looking good so far with the swap from the 3100. The only pita was finding the correct adapters for the fuel injector harness (ev1 to multec 2).

I've got the...
Forum: Technical Q&A 04-06-2015, 11:03 PM
Replies: 20
Views: 4,925
Posted By adrian13
I'm seeing a near future issue with number 2...

I'm seeing a near future issue with number 2 question: I deleted the egr (mms kit) but was thinking of putting a Pcv breather filter on the rear valve cover. There's no room though since the ignition...
Forum: Technical Q&A 03-30-2015, 11:35 AM
Replies: 20
Views: 4,925
Posted By adrian13
The entire motor has been overhauled: new crank,...

The entire motor has been overhauled: new crank, pistons, camshaft ... Which weight oil should I use to break it in?
Forum: Technical Q&A 03-27-2015, 09:19 PM
Replies: 20
Views: 4,925
Posted By adrian13
Thanks for the info. Also, just put 5w30...

Thanks for the info. Also, just put 5w30 conventional oil for the break in and then perform a motor oil flush right?
Forum: Technical Q&A 03-25-2015, 06:07 PM
Replies: 20
Views: 4,925
Posted By adrian13
LA1 Rebuild and Install

I am doing a motor swap from the 3100 to a 3400 and am getting really close to putting in the motor and tranny. I have several questions:

1. Which LA1 sensors do you recommend that I reuse or...
Forum: All Go (Performance modifications) 03-18-2015, 11:53 PM
Replies: 7
Views: 3,016
Posted By adrian13
Church auto in long beach. They're experienced in...

Church auto in long beach. They're experienced in hp tuners with a dyno.
Forum: All Go (Performance modifications) 03-17-2015, 12:40 AM
Replies: 2
Views: 996
Posted By adrian13
Siemens 60lb Injector (EV1) Adapter

Looking to see if anyone knows where I can find an adaptor the wire harness for the EV1 Siemens fuel injectors? I feel like I've looked all over.
Forum: Personal Vehicle News 09-22-2012, 05:09 PM
Replies: 39
Views: 3,222
Posted By adrian13
its because it gets aggravating, I'm human not a...

its because it gets aggravating, I'm human not a bot. I would like to get questions about the motor, answers, and responses on how to improve. I'm not gonna chill on the forum getting ripped like a...
Showing results 1 to 15 of 44

 
Forum Jump

All times are GMT -6. The time now is 12:07 PM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2011 GrandAmGT.com
RedlineGoods.com