Removing mirror joystick from window trim? - Page 2

AaronGTR · 12-07-2005, 10:37 AM

Anybody ever find a part number for that trim ring? I got mine out once successfully to paint the plate, but I took it out again to paint it a different color and the sucker broke this time. I guess if I can't find a part number I can get one from a junk yard, but that would cost more since I'd probably have to buy the whole panel switches and all and those are expensive.

It's that or glue the sucker in there permanent.

Vintalage · 12-07-2005, 02:00 PM

I'll have to see if I can find one. When I had to get my window regulator fixed (driver window stopped working), the dealer replaced the ring free of charge.

freakydeaky · 12-07-2005, 02:21 PM

Quote:

Originally Posted by AaronGTR

Anybody ever find a part number for that trim ring?

the switch bezel is included with the switch panel.... in the listing it shows no p/n for the ring bezel... see attachments

AaronGTR · 12-07-2005, 09:04 PM

Cool, got a part number for the switch panel? Thanks man.

GrahamKracka · 12-07-2005, 09:12 PM

mine just kind of fell out

freakydeaky · 12-08-2005, 10:21 AM

Quote:

Originally Posted by AaronGTR

Cool, got a part number for the switch panel? Thanks man.

no prob....
see attachment

DefaZe · 03-18-2009, 05:56 PM

umm bumping a completely dead thread... but does anyone know to put the inside of this back together?? I took it apart just to look at it because I was interested how the twisting thing worked, etc, and when I popped it apart like 15 little pieces shot out of nowhere and I now have no clue how to reassemble it.. Anyone??

tenspeed · 03-18-2009, 06:19 PM

You probably can't put it back together. It started out as one piece.

This has bits of paper to show where it broke

I put a wire tie on it.

PhantomLover007 · 03-18-2009, 06:21 PM

Sounds like you might as well get a new one from somewhere.

Kids....

Dont' feel bad. When I was putting the WFG on my HVAC, I toom apart the heater controls for some reason and parts flew out of that. It took me a bit to figure out how sh1t went back in..

DefaZe · 03-18-2009, 10:49 PM

Sorry there was apparently a misunderstanding. I meant the electrical components inside of the switch assembly, not the mounting hardware. I popped those tabs off on both sides that you can see in your 3rd picture, and it all came apart. There was 3-4 springs, 3 copper "arms," a black piece of plastic, a white piece of plastic, and then the circuit board...

And yea I did the same thing with the HVAC too PL

Took me a while to figure that bastard out..

DefaZe · 03-20-2009, 11:08 PM

???? Or does anyone at least have a part number for the whole knob

tenspeed · 03-21-2009, 07:20 AM

Quote:

Originally Posted by DefaZe

???? Or does anyone at least have a part number for the whole knob

Try a couple of ebay searches. Try using "Grand Am switch" and "Grand Am mirror". Sometimes you can get the door panel that has the window switches for less than the switch alone. Should be around $20.

PhantomLover007 · 03-21-2009, 08:29 AM

Quote:

Originally Posted by tenspeed

You probably can't put it back together. It started out as one piece.

This has bits of paper to show where it broke

I put a wire tie on it.

I'm going to have to try that Jim. I had a piece break completely off that's basically the size of where the paper is on your pics

The switch has a gangsta lean to it now...

DefaZe · 03-21-2009, 09:53 PM

haha is your switch ridin dirty

DefaZe · 03-21-2009, 10:06 PM

$10 shipped.

http://cgi.ebay.com/ebaymotors/GM-22...Q5fAccessories

chris_gt_74 · 03-30-2009, 08:07 PM

Mine was broke when I got my car and I took it apart and rigged it backed together with some intuitive thinking. If I had it off I'd post a pic of what I did to keep mine from falling through. Basically, I made myself a clip out of a piece of metal coat hanger and bent it all into the shape I wanted and drilled 2 small holes for each side of the clip to fit in. It fits very nicely and is still removable if I need to take it apart again. The whole little project took me about 10 minutes.

If anyone's interested in the pic, let me know and I'll go pop it out and snap a pic of the fixed "clip" attached to the panel.

ItsMeScottG · 07-11-2013, 10:40 PM

Quote:

Originally Posted by PhantomLover007

I'm going to have to try that Jim. I had a piece break completely off that's basically the size of where the paper is on your pics

The switch has a gangsta lean to it now...

Does anyone have a part number on this? Mine just broke today.

I know I'm bumping an old thread and all but this is what I could find.

rjs_boy · 07-12-2013, 01:51 AM

Quote:

Originally Posted by ItsMeScottG

Does anyone have a part number on this? Mine just broke today.

I know I'm bumping an old thread and all but this is what I could find.

I would definitely check with the vendor to verify the part numbers as the listing I have is quite old at this point...however the P/N I have are:

2003 Mirror Switch = 22624805

For the retaining ring part, it's only sold together with the 'switch panel'

2003 4 door = 22663005 (Power Windows)
2003 4 door = 22663003 (Manual Windows)

2003 2 door = 22663006 (Power Windows)
2003 2 door = 22663003 (Manual Windows)

blckgagt · 07-12-2013, 06:09 AM

Quote:

Originally Posted by ItsMeScottG

Does anyone have a part number on this? Mine just broke today.

I know I'm bumping an old thread and all but this is what I could find.

Mine broke a while back and i just ended up zip tieing the **** out of it....

. Ever since then, no problems.

ItsMeScottG · 07-12-2013, 02:26 PM

Quote:

Originally Posted by rjs_boy

I would definitely check with the vendor to verify the part numbers as the listing I have is quite old at this point...however the P/N I have are:

2003 Mirror Switch = 22624805

For the retaining ring part, it's only sold together with the 'switch panel'

2003 4 door = 22663005 (Power Windows)
2003 4 door = 22663003 (Manual Windows)

2003 2 door = 22663006 (Power Windows)
2003 2 door = 22663003 (Manual Windows)

Actually I went to the Chevy dealership today and they ordered just the retainer clip for me. They pulled up a diagram and showed me the part. It cost me $4.99, not too bad

12-07-2005, 10:37 AM	#21
AaronGTR BlingWithBallz AKA: Aaron Join Date: Aug 2002 Location: Detroit area, MI Age: 43 Posts: 12,254 Vehicle: 2000 Grand Am GT1 2dr	Anybody ever find a part number for that trim ring? I got mine out once successfully to paint the plate, but I took it out again to paint it a different color and the sucker broke this time. I guess if I can't find a part number I can get one from a junk yard, but that would cost more since I'd probably have to buy the whole panel switches and all and those are expensive. It's that or glue the sucker in there permanent. __________________ The few, the proud, the boosted! 13.788 @ 103.73 mph (3/2011) 320 whp and 300 ft/lbs torque. (3/2011) See it here. the total package.

12-07-2005, 02:00 PM	#22
Vintalage Hey paisanos! Join Date: Aug 2002 Location: Maryland Age: 38 Posts: 5,490 Vehicle: 2002 Grand Am GT1	I'll have to see if I can find one. When I had to get my window regulator fixed (driver window stopped working), the dealer replaced the ring free of charge. __________________ 2002 Grand Am GT1 Sedan - Black 7000K HID PICS [SOLD to Jscarano]

12-07-2005, 09:04 PM	#24
AaronGTR BlingWithBallz AKA: Aaron Join Date: Aug 2002 Location: Detroit area, MI Age: 43 Posts: 12,254 Vehicle: 2000 Grand Am GT1 2dr	Cool, got a part number for the switch panel? Thanks man. __________________ The few, the proud, the boosted! 13.788 @ 103.73 mph (3/2011) 320 whp and 300 ft/lbs torque. (3/2011) See it here. the total package.

03-18-2009, 06:19 PM	#28
tenspeed GAGT - Senior Member Join Date: Nov 2003 Location: Honeoye, NY Posts: 1,734 Vehicle: 02 GA 2.2L, 5 Speed	You probably can't put it back together. It started out as one piece. This has bits of paper to show where it broke I put a wire tie on it. __________________ ~Jim~ www.TeamGI.com - Western New York Cardomain page Click here to see my auctions

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-07-2005, 09:12 PM	#25
GrahamKracka WannaBe Fat Kid AKA: Richard Join Date: Aug 2004 Location: San Antonio, Texas Age: 36 Posts: 1,517 Vehicle: 2005 Nissan Titan	mine just kind of fell out

03-18-2009, 05:56 PM	#27
DefaZe GAGT - Member AKA: Steffan Join Date: Jan 2009 Location: Fairbanks, Alaska Age: 29 Posts: 260 Vehicle: 2000 Grand Am GT Sedan	umm bumping a completely dead thread... but does anyone know to put the inside of this back together?? I took it apart just to look at it because I was interested how the twisting thing worked, etc, and when I popped it apart like 15 little pieces shot out of nowhere and I now have no clue how to reassemble it.. Anyone??

03-18-2009, 10:49 PM	#30
DefaZe GAGT - Member AKA: Steffan Join Date: Jan 2009 Location: Fairbanks, Alaska Age: 29 Posts: 260 Vehicle: 2000 Grand Am GT Sedan	Sorry there was apparently a misunderstanding. I meant the electrical components inside of the switch assembly, not the mounting hardware. I popped those tabs off on both sides that you can see in your 3rd picture, and it all came apart. There was 3-4 springs, 3 copper "arms," a black piece of plastic, a white piece of plastic, and then the circuit board... And yea I did the same thing with the HVAC too PL Took me a while to figure that bastard out..

03-20-2009, 11:08 PM	#31
DefaZe GAGT - Member AKA: Steffan Join Date: Jan 2009 Location: Fairbanks, Alaska Age: 29 Posts: 260 Vehicle: 2000 Grand Am GT Sedan	???? Or does anyone at least have a part number for the whole knob

03-21-2009, 09:53 PM	#34
DefaZe GAGT - Member AKA: Steffan Join Date: Jan 2009 Location: Fairbanks, Alaska Age: 29 Posts: 260 Vehicle: 2000 Grand Am GT Sedan	haha is your switch ridin dirty

03-21-2009, 10:06 PM	#35
DefaZe GAGT - Member AKA: Steffan Join Date: Jan 2009 Location: Fairbanks, Alaska Age: 29 Posts: 260 Vehicle: 2000 Grand Am GT Sedan	$10 shipped. http://cgi.ebay.com/ebaymotors/GM-22...Q5fAccessories

03-30-2009, 08:07 PM	#36
chris_gt_74 N/A all the way AKA: Me Join Date: May 2008 Location: Texas Age: 47 Posts: 527 Vehicle: 2014 Mustang 3.7	Mine was broke when I got my car and I took it apart and rigged it backed together with some intuitive thinking. If I had it off I'd post a pic of what I did to keep mine from falling through. Basically, I made myself a clip out of a piece of metal coat hanger and bent it all into the shape I wanted and drilled 2 small holes for each side of the clip to fit in. It fits very nicely and is still removable if I need to take it apart again. The whole little project took me about 10 minutes. If anyone's interested in the pic, let me know and I'll go pop it out and snap a pic of the fixed "clip" attached to the panel.