Split Remote Wire

aiixon · 04-13-2009, 01:43 PM

So I'm putting in another amp for a sub, so my question is: Can I just tap in a wire into my original remote wire, a few inches from where it goes into the amp? It should work right? I just wanted to check.

burgett2103 · 04-13-2009, 01:49 PM

if its the same wire you had used before, which is still connected however you had it connected before, then yes it will work if you splice into it

04-13-2009, 02:00 PM

also as long as your seein around three volts from the turn on lead, the amp will turn on (most amps will)

BOOTMASTER · 04-13-2009, 06:08 PM

or just connect the other (2nd amps) wire into the 1st amps remote terminal and not bother with the splice...

Jake · 04-13-2009, 06:13 PM

Quote:

Originally Posted by BOOTMASTER

or just connect the other wire into the 1st amps remote terminal and not bother with the splice...

Word.

cardude007617 · 04-13-2009, 08:41 PM

word times three. just tie into your first amp's remote. works just fine and saves some screwing around doing it other ways.

oldinstaller · 04-13-2009, 09:36 PM

Yes, it will work.
You have my confirmation so go and make sound for all to hear and enjoy.

Good luck

aiixon · 04-14-2009, 07:20 PM

Okay awesome I'll just connect it to the other amp, thanks guys!

04-13-2009, 01:43 PM	#1
aiixon got ma permit! AKA: Steffan Join Date: Mar 2009 Location: 907 Age: 29 Posts: 830 Vehicle: 2000 GT Sedan	Split Remote Wire So I'm putting in another amp for a sub, so my question is: Can I just tap in a wire into my original remote wire, a few inches from where it goes into the amp? It should work right? I just wanted to check.

04-13-2009, 06:08 PM	#4
BOOTMASTER i like JL AUDIO AKA: Bruce Join Date: Apr 2006 Location: Zion, IL Posts: 429 Vehicle: 2002 gt coupe	or just connect the other (2nd amps) wire into the 1st amps remote terminal and not bother with the splice... Last edited by BOOTMASTER; 04-13-2009 at 06:41 PM.

04-13-2009, 08:41 PM	#6
cardude007617 mmm turbo boost AKA: Paul Join Date: Dec 2006 Location: Milwaukee WI Age: 31 Posts: 4,870 Vehicle: 2005 WRX Sedan 5 Speed	word times three. just tie into your first amp's remote. works just fine and saves some screwing around doing it other ways. __________________ http://www.cardomain.com/ride/2565053 -2005 World Rally Blue Subaru Impreza WRX Sedan: Tanabe Touring 3in catback, ERZ bellmouth catted downpipe, catless uppipe, SPT Pink springs, SPT short shifter, SPT intake, stereo, Cobb Accessport stage II, Prosport boost/oil temp/volt gauges, 35%, 17x8 Rota Torques, F/R strut braces It's what makes a Subaru, a Subaru.

04-13-2009, 09:36 PM	#7
oldinstaller used to install..... Join Date: Sep 2002 Location: San Diego, CA Posts: 150 Vehicle: 1999 Grand Am SE	Turn on wire Yes, it will work. You have my confirmation so go and make sound for all to hear and enjoy. Good luck __________________ senior installation guru mobile security advisor home audio/video design consultant

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-13-2009, 01:49 PM	#2
burgett2103 Sounds for Dayzzz AKA: Nick Join Date: Dec 2008 Location: Tonica, IL Age: 30 Posts: 1,886 Vehicle: 03 GAGT/98 Chevy 1500	if its the same wire you had used before, which is still connected however you had it connected before, then yes it will work if you splice into it

04-13-2009, 02:00 PM	#3
hahano404 Guest Posts: n/a	also as long as your seein around three volts from the turn on lead, the amp will turn on (most amps will)

04-14-2009, 07:20 PM	#8
aiixon got ma permit! AKA: Steffan Join Date: Mar 2009 Location: 907 Age: 29 Posts: 830 Vehicle: 2000 GT Sedan	Okay awesome I'll just connect it to the other amp, thanks guys!