David's N/A Build Thread - Page 7

stewartfn18 · 04-07-2009, 10:08 PM

Quote:

Originally Posted by XtremeGaGt00

after your car is in running order and i put my new turbo manifolds on we oughta hook up at byron...your no far from me, maybe 30-40 miles at most? im in romeoville

sounds like a plan, it would be nice to see a couple tastefully modified GA's at the track. id like to get some new numbers with the new motor, and im sure you feel the same. i mentioned something about going to byron to one of the other guys in this thread but he never responded.

mfuller · 04-07-2009, 10:47 PM

If I can get it running right, I'm game to running with ya'll at Byron.

XtremeGaGt00 · 04-08-2009, 05:45 AM

sounds like a plan to me, i guess we can get a date setup when were all closer to getting our projects done..because at this rate theres no saying when theyll be done....my car cant even pass emmissions so i cant drive it on the street

GrandAmGTTT · 04-19-2009, 03:56 PM

Quote:

Originally Posted by DumpsterDamon

when you realize it's only a grand am and get sick of putting money into it, i'll be waiting to say i told you so. fyi.

XtremeGaGt00 · 04-19-2009, 04:52 PM

Quote:

Originally Posted by DumpsterDamon

when you realize it's only a grand am and get sick of putting money into it, i'll be waiting to say i told you so. fyi.

wow..musta overlooked that..REALLY DUDE?..seriously stfu and gtfo

stewartfn18 · 04-19-2009, 05:00 PM

Quote:

Originally Posted by XtremeGaGt00

wow..musta overlooked that..REALLY DUDE?..seriously stfu and gtfo

that was one of the first posts made in this thread. Needless tpo say what he said hasnt happened, almost,but almost only counts in horseshoes and hand grenades.

Back on topic, my Comp ported 3500 LIm camein yesterday. Headers should be shipped out tomorrow, and ill be sending in my UIM to be ported at the end of the month. Then im only waiting on a Fuel rail and Injectors from another member, then a tune and its done.

Grandamgtblk99 · 04-19-2009, 05:08 PM

Can't wait to see the results of this build.

GrandAmGTTT · 04-19-2009, 06:16 PM

Nice! are you using the 3400 upper with the 3500 LIM? and what headers you get?

stewartfn18 · 04-20-2009, 03:22 PM

Quote:

Originally Posted by GrandAmGTTT

Nice! are you using the 3400 upper with the 3500 LIM? and what headers you get?

yes thats what im doin, and i got s&s headers

stewartfn18 · 04-24-2009, 09:58 PM

liitle preview. i dont have any more parts, but i took it out of the bag to make sure everything was still good and saw an opprotunity.

GrandAmGTTT · 04-25-2009, 08:27 AM

Nice man its looking good!

PhantomLover007 · 04-25-2009, 10:23 AM

Nice and clean David

SilverGAGT2002 · 04-25-2009, 11:30 AM

Very nice

About how much have you spent doing this?

stewartfn18 · 04-25-2009, 12:11 PM

~2500-3000

SilverGAGT2002 · 04-25-2009, 01:48 PM

Not bad at all im using TOG headers instead of S&S i plan on doing the same after i get my headers coated and put on.

stewartfn18 · 04-27-2009, 11:49 AM

still dont have my headers, but i just purchased my Comp ported 3400 UIM. ill be taking to ups here shortly.

lvemy3100 · 04-27-2009, 11:57 AM

headers are on the way

stewartfn18 · 04-27-2009, 12:05 PM

Quote:

Originally Posted by lvemy3100

headers are on the way

awesome. mark did you get my pm?

stewartfn18 · 04-28-2009, 03:24 PM

headers came in

timberwoof · 04-28-2009, 03:50 PM

Nice. About how much more do you have to do? Are you getting lightened or underdrive pulley?

04-07-2009, 10:47 PM	#122
mfuller Mr. Common Sense AKA: Matt Join Date: Aug 2002 Location: Loves Park, IL USA Age: 47 Posts: 2,031 Vehicle: 2000 Alero GLS sedan	If I can get it running right, I'm game to running with ya'll at Byron. __________________ Matt - Resident brake and suspension guru Also, your friendly Performance and Technical Moderator *Please don't tailgate, text and drive, drink and drive, or otherwise act like an asshat.* Questioning if it will ever run again.....

04-08-2009, 05:45 AM	#123
XtremeGaGt00 converted to ls1 :) AKA: Jason Join Date: Nov 2003 Location: romeoville, il Age: 36 Posts: 916 Vehicle: 00gagt 99gtp 99t/a	sounds like a plan to me, i guess we can get a date setup when were all closer to getting our projects done..because at this rate theres no saying when theyll be done....my car cant even pass emmissions so i cant drive it on the street __________________ 00 GaGt turbo/camm'd SOLD!13.68 @100.34.. 2.0 60' w/ slipping trans...stock cam/stock 103xxx bottom end 99 GTP demodded! 12.8 @107.19.. 1.7 60' on 555r's 99 Trans Am6.0 lq4,studded,t76 turbo, turbo cam, 3.5in exhaust,#80's,dual walbros,ford 9in rear, adj, tq arm, adj, control arms,160 stat,ls6 intake,555r's 11.8 @122.<<--nitrous only times

04-19-2009, 05:08 PM	#127
Grandamgtblk99 Burgee AKA: Allen Join Date: Mar 2006 Location: Orange, Tx Age: 39 Posts: 787 Vehicle: 1999 Grand Am Gt	Can't wait to see the results of this build. __________________ 1999 Sc/t turbo.

04-19-2009, 06:16 PM	#128
GrandAmGTTT Pontiac Club Toledo AKA: Josh Join Date: Dec 2007 Location: Temperance, Michigan Posts: 390 Vehicle: 1999 Grand Am GT sedan	Nice! are you using the 3400 upper with the 3500 LIM? and what headers you get? __________________ Pontiac Fuel For Your Soul!! Pontiac Club of Toledo- President Ohio Northern University Automotive Club- Vice President Flowmaster 80, MDS 8.5mm wires, NGK plugs, LS1 MAF, 65mm TCE TB, MPracing p&p UIM, EGR delete, CAI, heat shield tape, Custom tuned by Chris , ZEX wet kit, ac delete, Front+Rear drilled/slotted rotors, Eibach springs, Front+Rear strut bars, ported and matched 3500 UIM and 3400 LIM, Powder coated Upper/Lower Intake manifolds and valve covers Last edited by GrandAmGTTT; 04-19-2009 at 06:19 PM.

04-24-2009, 09:58 PM	#130
stewartfn18 GAGT - Senior Member AKA: David Join Date: Jun 2007 Location: Oldsmar,FL Age: 32 Posts: 2,049 Vehicle: 04 vette, 14 R6	liitle preview. i dont have any more parts, but i took it out of the bag to make sure everything was still good and saw an opprotunity. Attached Thumbnails __________________ MODS: Not Enough

04-25-2009, 08:27 AM	#131
GrandAmGTTT Pontiac Club Toledo AKA: Josh Join Date: Dec 2007 Location: Temperance, Michigan Posts: 390 Vehicle: 1999 Grand Am GT sedan	Nice man its looking good! __________________ Pontiac Fuel For Your Soul!! Pontiac Club of Toledo- President Ohio Northern University Automotive Club- Vice President Flowmaster 80, MDS 8.5mm wires, NGK plugs, LS1 MAF, 65mm TCE TB, MPracing p&p UIM, EGR delete, CAI, heat shield tape, Custom tuned by Chris , ZEX wet kit, ac delete, Front+Rear drilled/slotted rotors, Eibach springs, Front+Rear strut bars, ported and matched 3500 UIM and 3400 LIM, Powder coated Upper/Lower Intake manifolds and valve covers

04-25-2009, 11:30 AM	#133
SilverGAGT2002 GTslow AKA: David Join Date: Mar 2009 Location: Odessa, TX Age: 32 Posts: 1,136 Vehicle: 02 Grand Am GT Sedan	Very nice About how much have you spent doing this? __________________ Nothing Coming soon!

04-25-2009, 12:11 PM	#134
stewartfn18 GAGT - Senior Member AKA: David Join Date: Jun 2007 Location: Oldsmar,FL Age: 32 Posts: 2,049 Vehicle: 04 vette, 14 R6	~2500-3000 __________________ MODS: Not Enough

04-25-2009, 01:48 PM	#135
SilverGAGT2002 GTslow AKA: David Join Date: Mar 2009 Location: Odessa, TX Age: 32 Posts: 1,136 Vehicle: 02 Grand Am GT Sedan	Not bad at all im using TOG headers instead of S&S i plan on doing the same after i get my headers coated and put on. __________________ Nothing Coming soon!

04-27-2009, 11:49 AM	#136
stewartfn18 GAGT - Senior Member AKA: David Join Date: Jun 2007 Location: Oldsmar,FL Age: 32 Posts: 2,049 Vehicle: 04 vette, 14 R6	still dont have my headers, but i just purchased my Comp ported 3400 UIM. ill be taking to ups here shortly. __________________ MODS: Not Enough

04-27-2009, 11:57 AM	#137
lvemy3100 Im President Charley AKA: mp Join Date: Dec 2005 Location: place Posts: 2,040 Vehicle: 01 car	headers are on the way __________________ -Mark You want more power? You need MP Racing! ------ Now drink with me deeply of the bourbon, scotch, and rye until such time as we are fighting drunk. Then we shall find, and beat the a**es of, the nonbelievers who ruined my feast.

04-28-2009, 03:24 PM	#139
stewartfn18 GAGT - Senior Member AKA: David Join Date: Jun 2007 Location: Oldsmar,FL Age: 32 Posts: 2,049 Vehicle: 04 vette, 14 R6	headers came in __________________ MODS: Not Enough

04-28-2009, 03:50 PM	#140
timberwoof Law Dawg AKA: Cody Join Date: Jul 2006 Location: Portland Tx Posts: 1,827 Vehicle: 2004 Grand Am SE1	Nice. About how much more do you have to do? Are you getting lightened or underdrive pulley? __________________ Mods: Sways, F-STB, Dr. Speed Stage 2 w/ box, Rear Disk Conversion, drilled rotors, steel braided lines, 180* T-Stat.