3400 complete partout - performance parts!

[mfuller]

I sent you a PM on the lifters a few days ago.....

[Rootie524]

sorry i missed it when i was going through my pms. you can have them im just waiting till more stuff sells to give me reason to rip the engine apart. obviously (and i hope you can understand) im not going to rip apart the top end just for lifters. but it looks like most of the stuff will sell within the next week so ill keep ya posted. thanks

[mfuller]

No worries; I understand.

[Ceej]

is the intake still available?

[Rootie524]

still got it

[Ceej]

I'll take it for 50

[Rootie524]

PM sent

[HOYS]

Are those 3400 or 3.5 heads?

[Rootie524]

They are 3400 heads. degreased, resurfaced, exhaust ports smoothed out a bit, and two head studs needed to be drilled out and helicoied. comes with head studs already installed, good to go.

[Rootie524]

CAI is sold. everything else is still available. for those waiting for me to pull more internal parts. expect a pm within the next week or two. been busy.

[13's_or_bust]

would you hold onto to the cam for maybe a month to a month and a half? id buy everything needed for the cam swap. with no questions asked and i would give you exactly what you asking for, for all of the parts. cam, valve springs, pushrods, lifters everything i would need for the cam swap i will buy. also i will buy the set of exhaust manifolds if they are from the 3400. please let me know with a pm if you will hold onto the parts for me. thank you jonny.

[Rootie524]

i already have someone in line for the cam parts and all that. but if that deal falls through your next.

as for the exhaust manifolds. yes, 3100/3400 have the same manifolds. so if you want those can definitely be yours. let me know, thanks.

[13's_or_bust]

god i hope it falls through . i really want this cam it sounds so good in your vids, i want to hear it open dp so bad . i will try my hardest to get the money even earlier for you. i also need these parts shipped im in 46323 area code.

i didnt know the ex. manis from a large port 3100 are the same as the 3400 ones. the 3100 are like a header type in the rear?

[Weman]

Pm me shipping on ac compressor to

208 wood land drive
keswick, on
Canada
l4p2m8

or

3909 Witmer Road.
Niagara Falls, NY 14305

[Rootie524]

Originally Posted by 13's_or_bust

god i hope it falls through . i really want this cam it sounds so good in your vids, i want to hear it open dp so bad . i will try my hardest to get the money even earlier for you. i also need these parts shipped im in 46323 area code.

i didnt know the ex. manis from a large port 3100 are the same as the 3400 ones. the 3100 are like a header type in the rear?

well it all depends. the large port 3100 and 3400 have the same exhaust manifolds. however, i believe they are different from 3100 sp to 3100 lp but im not 100% sure. most of my time has been spent on 3100/3400 lps. does your engine have the upper intake manifold with the lines running across it or is it a smooth surface with 3100 printed on it.

[ioseida]

Hey how many miles you got on that throttle body? I think I might need one!! pm me the shipping to 90007 LA, CA. thanks

[Rootie524]

PMs sent on AC comp and throttle body.

for those wondering engine should be pulled in the next week or two.

[GRAND-AM-SE]

Originally Posted by Rootie524

well..it's over. I'm done with this car. everything must go.

custom comp cam (pm for specs) - $250 includes pushrods
pushrods to go with - $50 if not sold with cam
lifters w/ TCE springs installed - $50
LIM - $40
(2) UIM - $20
exhaust manifolds - $40 for a set or $25 a piece (comes with crossover)
crankshaft - $50
speed pro hypereutectic pistons (30 over..professionally attached to rods) - $100
3400 block freshly bored 30 over with new cam bearings and plugs - $200
set of heads - $100
cleaned valves - $40
26986 valve springs - $60
oil pan - $40
throttle body - $20
o2 sensors - $35 each
cold air intake (fender wall) - SOLD
cruise control unit - $15
(2) AC compressor - $50
stock camshaft - $40

ask for pictures. ---interior parts also available upon request.

i could sit here naming parts all day..but I won't. you need a part not listed im sure i have it. inquire below. all payments via paypal. will take offers on everything. thanks.

u got gt bumpers? and sides? im from pa too

[Rootie524]

no, this vehicle is a chevy malibu. sorry for confusion.

and just to update. the engine is getting pulled tomorrow. so any and all engine parts will be readily available!!

also I have a BRAND NEW AC Delco Ignition Control Module for sale. for the 3x00 engine.

[13's_or_bust]

my uim has the lines going across but ill be using the large port 3100 without the lines on my 3500.