Pics for all who said it couldnt be done....hid dual halo projectors

[ancona46]

i clicked it and seen nice lights was there something else i missed?

i know about the driver side i plan on aiming it down as soon as i get a chance

[gaowners32]

What was exactly required to make the hids work? in place of whatever h1 or h3 bulb that the light needs.

[ancona46]

just the bulbs and ballast..and some trimming to the base of the bulbs

[Big T]

Originally Posted by GA SE/T

Not to hijack this thread but post #48.

Different halo projectors

It was misinformation. HIDs do not out out more heat than stock. No fear of Melting

[Big T]

Originally Posted by ancona46

just the bulbs and ballast..and some trimming to the base of the bulbs

any pics of the trimming that needed to be done. also i saw the pics you took of the headlight instal, Geez that was alot of hacking. i`d love to see a pic of your housings before and after or even side by side with stock, just to get an idea before i start hacking away. I just bought a GA and this is def the mod on the top of my list!

[ancona46]

no i didnt take of pics of the bulbs but i gotta take off the headlights sometime soon to seal them up better they are fogging ill snap a pic then

[JRYAN34]

I was thinking about getting these.....

Can you use 9007 HIDs?
How much cutting if actually needed?
Are the headlights themselves actually plug and play or do you need another switch for the halo rings?

[ryanbgb22]

Originally Posted by JRYAN34

I was thinking about getting these.....

Can you use 9007 HIDs?
How much cutting if actually needed?
Are the headlights themselves actually plug and play or do you need another switch for the halo rings?

as answered in you other thread..... You CANNOT use 9007 bulbs! Cant be done, stop asking. You saw the pics posted in your thread of the cutting that is necessary.
It's up to you on how the halos get wired, so they can work however/whenever you want.

****

[boost21]

Originally Posted by JRYAN34

I was thinking about getting these.....

Can you use 9007 HIDs?
How much cutting if actually needed?
Are the headlights themselves actually plug and play or do you need another switch for the halo rings?

[SSRacer]

You should definitely do a how to write up on this. I have a set of these being delivered today and may swap to HID in the future. No money to do it now, so I'll just have to rock the halogens for a while.

[ancona46]

im too lazy to type it up

all it is

cut bracket
hook up lights
install hid kit if u choose
stick lights in the car

hope u dont drive alot at night thats halogen's blow

[SSRacer]

I don't drive much at night, mostly just to work and back these days. We usually take the wife's Santa Fe for our running around (easier to get the baby in and out of).

I'm gonna run to pep boys in the morning and get some better bulbs than what they came with before I install. Hopefully that will help a bit.

Did you dissable the DRLs? Just curious cause I might tackle that tomorrow too.

As for the writeup, I was thinking more about the HID's as I have zero experience with them.

[PhantomLover007]

Damn finally able to see pics since they put internet in our living area.

DAMN GOOD JOB MIKE!!!

[ancona46]

Originally Posted by SSRacer

I don't drive much at night, mostly just to work and back these days. We usually take the wife's Santa Fe for our running around (easier to get the baby in and out of).

I'm gonna run to pep boys in the morning and get some better bulbs than what they came with before I install. Hopefully that will help a bit.

Did you dissable the DRLs? Just curious cause I might tackle that tomorrow too.

As for the writeup, I was thinking more about the HID's as I have zero experience with them.

for the hids since h1 isnt plug and play with 9007 you just find the + and - in the factory harness and tie the + and - from the hid kit into that its really simple if u have a volt meter

[SSRacer]

Cool. I'll probably look into that after the first of the year. Getting ready to install mine now. Got some Sylvania Silver Star bulbs for it. Just got done verifying that everything works, now I'm getting ready to cut.