GrandAmGT.com Forum
http://www.pfyc.com GrandAmGT.com Premium Memership Signup
RotorsOnline.com   

Go Back   GrandAmGT.com Forum > GAGT - Technical - Sponsored by www.MilzyMotorSports.com > Technical Q&A

Reply
 
Thread Tools Display Modes
Old 10-01-2002, 12:49 PM   #1
NeonGA
Biff Tannon
 
Join Date: Aug 2002
Location: Erie, PA
Age: 37
Posts: 99
NeonGA Gettin' there
Send a message via AIM to NeonGA
Please Read If You Know Alot About Cars

hey....I am trying to pull out my engine but it wont come out....everything is diconected that i can think of....is there any hidden bolts that hold the tranny to the block? The passenger side is free, the driver side is not coming out
__________________
00' Grand Am SE 3.4
ROLLIN ON NUTTIN BUT AIR

CHECK OUT MY RIDE!!!!!
NeonGA is offline   Reply With Quote
Old 10-01-2002, 12:51 PM   #2
Tonyyank
Administrator
 
Tonyyank's Avatar
 
AKA: Anthony
Join Date: Aug 2002
Location: Parma, MI
Age: 39
Posts: 3,470
Vehicle: 09 Silverado 4x4
Tonyyank has disabled reputation
Send a message via AIM to Tonyyank Send a message via Yahoo to Tonyyank
Maybe it's all that manure that was dumped on top of you car.....

I'm sorry, I had too...
Tonyyank is offline   Reply With Quote
Old 10-01-2002, 12:54 PM   #3
NeonGA
Biff Tannon
 
Join Date: Aug 2002
Location: Erie, PA
Age: 37
Posts: 99
NeonGA Gettin' there
Send a message via AIM to NeonGA
it took me a second to figure out what you were talking about then i just laughed my ass off
__________________
00' Grand Am SE 3.4
ROLLIN ON NUTTIN BUT AIR

CHECK OUT MY RIDE!!!!!
NeonGA is offline   Reply With Quote
Old 10-01-2002, 01:02 PM   #4
iceman
woop woop
 
iceman's Avatar
 
AKA: Seth
Join Date: Aug 2002
Location: Cherry Hill, NJ
Age: 40
Posts: 10,528
Vehicle: 97 Blazer - 84 Fiero
iceman has disabled reputation
Send a message via AIM to iceman Send a message via Yahoo to iceman
Chris... post in the correct section with a topic that actually has something to do with the thread .. Thanks
iceman is offline   Reply With Quote
Old 10-01-2002, 01:06 PM   #5
ArcticWhiteSE
Covered in bees.
 
ArcticWhiteSE's Avatar
 
AKA: Rainier
Join Date: Apr 2001
Location: Arlington, WA
Age: 35
Posts: 494
Vehicle: 2013 Ram 5500
ArcticWhiteSE Gettin' there
Send a message via AIM to ArcticWhiteSE
yeah man, je$u$

I get b itch slapped everytime I make a goof on posting, you've been here longer than me too....

God I love your car Neon....
(gotta keep it real with the arctic white brothers ya undastand?)

Lataz..

--Arctic--
__________________
Quote:
Originally Posted by Jeremy
gotta learn the f'd up way I run this trainwreck


Quote:
Originally Posted by SikMindz View Post
WTH does sexuality have to do with pancakes?



ArcticWhiteSE is offline   Reply With Quote
Old 10-01-2002, 01:15 PM   #6
Jeremy
Unpimped my Mazda
 
Jeremy's Avatar
 
AKA: Jeremy
Join Date: Aug 2002
Location: 'Burb of Chicago
Age: 44
Posts: 1,828
Vehicle: 07 Tahoe LTZ ,12 Jetta
Jeremy a trusted member
Per my Service Manuals:

Disconnect the negative battery cable.
Drain the engine coolant.
Remove the engine air cleaner assembly.
Remove the hood.
Remove the drive belt.
Remove the hoses from the surge tank.
Remove the cruise control module.
Remove the engine wiring harness from the top of the engine. Refer to Harness Routing Views in Wiring Systems. Set the harness aside.
Disconnect the throttle cable.
Disconnect the cruise control cable.
Raise and suitably support the vehicle.
Remove the starter.
Remove the air conditioning (A/C) compressor with the lines attached.
Position the air conditioning (A/C) compressor aside.
Disconnect and position aside the lower engine wiring harness. Disconnect the catalytic converter flange from the rear exhaust manifold.
Remove the torque converter cover and the torque converter to flywheel bolts.
Remove the engine splash shields.
Remove the transaxle to engine brace.
Remove the 2 outer transmission mounting bolts.

Disconnect the upper and the lower radiator hoses.
Lower the vehicle.
Disconnect the fuel lines from the engine.
Disconnect the engine vacuum hoses to the brake booster.

Disconnect the heater hoses.
Install the engine support fixture
Raise the engine.
Remove the engine mount and the adapter.
Remove the power steering pump.
Install the engine lifting device.
Remove the engine support fixture.
Remove the transaxle to the engine retaining bolts.
Remove the engine from the vehicle.
Remove the engine flywheel.
Mount the engine onto a suitable engine stand.
__________________
Jeremy

12 VW Jetta

07 Tahoe LTZ 4x4

Over the firewall, out the antenna, into the router, shot to the modem, out the transponder, bounce into space, off the satellite, over their firewall, into the forums .... nothing but NET
Jeremy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 03:30 PM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright 2011 GrandAmGT.com
RotorsOnline.com