GrandAmGT.com Forum
http://www.pfyc.com GrandAmGT.com Premium Memership Signup
RotorsOnline.com   

Go Back   GrandAmGT.com Forum > GAGT - Main - Sponsored by www.PFYC.com > Newbies & FAQs > Help Me Decide

Reply
 
Thread Tools Display Modes
Old 06-03-2008, 02:39 PM   #1
zukiracer19
BoOsTiN'
 
zukiracer19's Avatar
 
AKA: slograndam
Join Date: Sep 2007
Location: State College, PA
Posts: 2,700
Vehicle: ev0m0de
zukiracer19 Still kinda new, but learning
Guys can you give me your input??

This is what i want to do with my car, get whatever is wrong with it fixed,
just got an AEM cold air intake(custom), AEM Bypass Valve, Getting EXHAUST(not sure , cat back high flow(not getting borla) , Spark plug wire/ plugs, DHPCM, Small Pulley(ac disconnect), Milzymotorsports Turbo Kit, is that a good setup?
zukiracer19 is offline   Reply With Quote
Old 06-03-2008, 03:01 PM   #2
GrandAmGT1996
letstrysupercharged?
 
GrandAmGT1996's Avatar
 
AKA: Brandon
Join Date: Jun 2005
Location: Lancaster, PA
Age: 29
Posts: 2,355
Vehicle: celica&boosted mustang
GrandAmGT1996 Gettin' there
Send a message via AIM to GrandAmGT1996
just buy rims/sct kit/lower. It will be much easier...plus theres no where to go fast around here anyway, except maple grove.
__________________
Quote:
Originally Posted by CantBeatIt96 View Post
that fart can, is a $200 can, its a skunk2 turbo mega power can, its bad ass. its the thing that gets my car the most creds
94 Celica - Lowered 4", tint, rims

[SOLD] '01 R6 (limited edition) - Akrapovic exhaust, Scotts Performance Steering Stabilizer, Penske Rear Suspension, Racetech Front Suspension, K&N Jet Kit, and more things I'm probably forgetting.
GrandAmGT1996 is offline   Reply With Quote
Old 06-03-2008, 03:01 PM   #3
timberwoof
Law Dawg
 
timberwoof's Avatar
 
AKA: Cody
Join Date: Jul 2006
Location: Portland Tx
Posts: 1,827
Vehicle: 2004 Grand Am SE1
timberwoof a trusted member
you may be able to piece a tubo kit together for cheaper.
__________________
Mods: Sways, F-STB, Dr. Speed Stage 2 w/ box, Rear Disk Conversion, drilled rotors, steel braided lines, 180* T-Stat.
timberwoof is offline   Reply With Quote
Old 06-03-2008, 03:34 PM   #4
Bryan
GAGT - Junkie
 
Bryan's Avatar
 
AKA: Bryan
Join Date: Dec 2006
Location: Sterling Heights, MI
Age: 28
Posts: 4,269
Vehicle: '09.5 G6
Bryan a trusted member
Isn't your car way up there in miles?
__________________
CarDomain (Updated 10/9)
Bryan is offline   Reply With Quote
Old 06-03-2008, 03:36 PM   #5
zukiracer19
BoOsTiN'
 
zukiracer19's Avatar
 
AKA: slograndam
Join Date: Sep 2007
Location: State College, PA
Posts: 2,700
Vehicle: ev0m0de
zukiracer19 Still kinda new, but learning
just hit 90K a little bit ago... so not really. and i go to maple grove a lot lately, i wouldnt mind bracket racing there runnin 13s
zukiracer19 is offline   Reply With Quote
Old 06-03-2008, 03:39 PM   #6
notsoaveragej0e
Causes a ruckus
 
notsoaveragej0e's Avatar
 
AKA: Joe
Join Date: Jun 2004
Location: Detroit, MI
Age: 30
Posts: 5,011
Vehicle: Maligoat
notsoaveragej0e has disabled reputation
Quote:
Originally Posted by zukiracer19 View Post
just hit 90K a little bit ago... so not really. and i go to maple grove a lot lately, i wouldnt mind bracket racing there runnin 13s
with 90k miles, you might get a couple runs in on boost before you grenade the engine... unless you plan on rebuilding it and replacing most things in it.
__________________
notsoaveragej0e is offline   Reply With Quote
Old 06-03-2008, 03:41 PM   #7
zukiracer19
BoOsTiN'
 
zukiracer19's Avatar
 
AKA: slograndam
Join Date: Sep 2007
Location: State College, PA
Posts: 2,700
Vehicle: ev0m0de
zukiracer19 Still kinda new, but learning
milzy was making a pretuned pcm so it wouldnt nade ur engine, or dont it matteR?
zukiracer19 is offline   Reply With Quote
Old 06-03-2008, 03:53 PM   #8
notsoaveragej0e
Causes a ruckus
 
notsoaveragej0e's Avatar
 
AKA: Joe
Join Date: Jun 2004
Location: Detroit, MI
Age: 30
Posts: 5,011
Vehicle: Maligoat
notsoaveragej0e has disabled reputation
Quote:
Originally Posted by zukiracer19 View Post
milzy was making a pretuned pcm so it wouldnt nade ur engine, or dont it matteR?
no I'm saying with that many miles, something is likely to bust- you could throw a rod, bomb the trans, or who knows what else on that engine... they aren't known as being bulletproof like a 3800.
__________________
notsoaveragej0e is offline   Reply With Quote
Old 06-03-2008, 03:56 PM   #9
zukiracer19
BoOsTiN'
 
zukiracer19's Avatar
 
AKA: slograndam
Join Date: Sep 2007
Location: State College, PA
Posts: 2,700
Vehicle: ev0m0de
zukiracer19 Still kinda new, but learning
i only plan on putting like 6 lbs of boost, i dont think it would kill my tranny too bad. motor idk beating it every now nd again
zukiracer19 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 11:50 AM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 2011 GrandAmGT.com
RotorsOnline.com