GrandAmGT.com Forum
http://www.pfyc.com GrandAmGT.com Premium Memership Signup
RedlineGoods.com   

Go Back   GrandAmGT.com Forum > GAGT - Technical - Sponsored by www.MilzyMotorSports.com > Technical Q&A

Reply
 
Thread Tools Display Modes
Old 04-15-2013, 11:26 AM   #1
BryanS1978
GAGT - Newbie
 
AKA: Bryan
Join Date: Apr 2009
Location: Tampa Florida
Posts: 6
Vehicle: 1995 GAGT
BryanS1978 Gettin' there
obd2 conversion

What's up everyone. Been awhile since I posted here and I have checked numerous sites and came up empty handed. I have a 95 gagt that I swapped the NVG 5sp in a while back and I also turbo'd the thing. Since I was obd1.5 there wasn't anything I could do so I ran the car without the charge pipes. Lame I know. Anyway I'm looking for some info as to how or will this work. I have a 98 V6 gagt ecm and engine harness and a 98 gase quad/5sp interior harness. Now I got the interior harness in already about to lay the new carpet. I just want to know if those 2 harnesses are going to work together and allow for me to get a tune and finally run boost. If the tach doesn't work, that's the least of my worries.

I've been searching alot from the 3rd Gen j-bodies sites and no mention of them swapping the interior harness but often times the tach and/or the fuel gauge doesn't work.

Any 4cyl guys swap a V6 before?? Any issues??
BryanS1978 is offline   Reply With Quote
Old 04-16-2013, 03:14 PM   #2
BryanS1978
GAGT - Newbie
 
AKA: Bryan
Join Date: Apr 2009
Location: Tampa Florida
Posts: 6
Vehicle: 1995 GAGT
BryanS1978 Gettin' there
What I mean is has there been anyone who swapped from a quad 4 to a 3X00 V6 on this board. If so the question was did the quad 4 dash harness work with the ecm and the V6 engine harness?? This is esentually what I am doing. My car was gutted down to the shell back in November so I have a obd2 engine harness and ecm from a 98gagt and the interior/dash harness from a 98gase.
BryanS1978 is offline   Reply With Quote
Old 04-16-2013, 03:37 PM   #3
sleepyalero
▂ ▃ ▅ ▆ █ ▆ ▅ ▃ ▂
 
sleepyalero's Avatar
 
AKA: Nathan
Join Date: Jul 2011
Location: Unknown.
Posts: 5,909
Vehicle: 2001 olds alero GLS
sleepyalero a trusted member
i want pics of this turbo ga....

as for the 4cyl to v6 ive heard there is a few problems you run into but i forget, i know the 4 cyl doesnt have a MAF. so you would need the wiring for a maf for the 3400
__________________
2001 | Alero GLS | 3400 | 6MT


2012 BMW S1000RR, full exhaust, power commander 5, dyno tune, 190WHP.
sleepyalero is offline   Reply With Quote
Old 04-16-2013, 03:46 PM   #4
BryanS1978
GAGT - Newbie
 
AKA: Bryan
Join Date: Apr 2009
Location: Tampa Florida
Posts: 6
Vehicle: 1995 GAGT
BryanS1978 Gettin' there
I will get pics soon. My old motor got trashed due to the camshaft pin shearing off and bent all the valves. So now is a new motor with my old rods and pistons and the heads got fixed. Just bent the valves and nicked the pistons. My old setup was log mani's. Now I got 2 3500 front manifolds. The crossover isn't complete so the turbo is not on the car at the moment. . Here's a video of just the rear of the car. Mainly for the sound.
BryanS1978 is offline   Reply With Quote
Old 04-16-2013, 04:00 PM   #5
BryanS1978
GAGT - Newbie
 
AKA: Bryan
Join Date: Apr 2009
Location: Tampa Florida
Posts: 6
Vehicle: 1995 GAGT
BryanS1978 Gettin' there
http://m.youtube.com/#/watch?v=EUAmhtdawFg

See if that works.
BryanS1978 is offline   Reply With Quote
Old 04-16-2013, 04:21 PM   #6
sleepyalero
▂ ▃ ▅ ▆ █ ▆ ▅ ▃ ▂
 
sleepyalero's Avatar
 
AKA: Nathan
Join Date: Jul 2011
Location: Unknown.
Posts: 5,909
Vehicle: 2001 olds alero GLS
sleepyalero a trusted member
worked. didnt sound bad.
__________________
2001 | Alero GLS | 3400 | 6MT


2012 BMW S1000RR, full exhaust, power commander 5, dyno tune, 190WHP.
sleepyalero is offline   Reply With Quote
Old 04-16-2013, 05:51 PM   #7
BryanS1978
GAGT - Newbie
 
AKA: Bryan
Join Date: Apr 2009
Location: Tampa Florida
Posts: 6
Vehicle: 1995 GAGT
BryanS1978 Gettin' there
Thanks, I thought it sounded to raspy. Anyway, I got the shortstar's 65mm TB and a custom ground cam from comp. Apparently I had some overly stiff springs. Now I got the blues from wot. Other than ported and polished heads, the whole motor is a 2000+ model 3100 with the better flowing heads and now I got the 3500 front exhaust manifolds on front and back. I got a LSD insert in the trans, and a clutch masters clutch. 2.5" exhaust all the way back going thru a greddy fart can. Lol
BryanS1978 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 11:24 PM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 2011 GrandAmGT.com
RedlineGoods.com